G. E. Shears Electric serves Arcadia and the surrounding Los Angeles County area with residential and commercial electrical work, any hour of the day or night. Whether you have a dead outlet at midnight or need a full panel upgrade scheduled for next week, we pick up the phone and get it handled. Work is performed by licensed electricians, same-day appointments are often available, and the rate is confirmed before anything is scheduled.
Quick response. Code-correct work. Tidy finish.
Call (626) 929-3282 for a quote.
Whether this is your first repair or your tenth, the process starts the same way: you describe what you are seeing, and we figure out what is causing it. Dead outlets, flickering lights, tripping breakers, and rooms with no power at all are the calls we get most often. Each one points to something specific in the wiring, and finding that something is the job.
We check the obvious first and work back from there. Loose connections, overloaded circuits, damaged wiring, and failing devices all show up in similar ways. GFCI and AFCI protection failures are common in kitchens, bathrooms, and garages, and grounding and bonding issues can create problems that are easy to miss without a proper diagnostic.
We trace the fault. We fix the wiring. We restore the power.
Older panels were built for a different era of electrical demand. If your home or building is still running on a fuse box, or if a 100-amp service is struggling to keep up with modern loads, a panel upgrade is usually the right next step.
We handle panel replacements, 200-amp service upgrades, fuse-box-to-breaker conversions, subpanel installation, and load calculations. For homeowners planning a remodel or addition, we can walk through what the new load will require before a single wall is opened. For property managers working with older buildings, we assess what the existing service entrance and meter setup can support and what needs to change.
Wiring work checked against code before sign-off means the upgrade is done right the first time. Let us handle the panel and the permits.
A properly wired home is a safer home, and that standard applies whether we are adding a single outlet or rewiring an entire floor. We install GFCI outlets in wet areas, AFCI outlets in bedrooms and living spaces, USB outlets where they make sense, and outdoor-rated outlets for patios and garages.
Switch and dimmer installation, whole-home rewiring, and partial rewiring for additions or renovations all fall within our regular scope. Homes in Arcadia with knob-and-tube wiring or aluminum branch-circuit wiring get particular attention. Both create real hazards when left in place, and we handle the remediation and replacement work to bring those circuits up to current code.
All outlet and switch work is code-compliant as a matter of course, not as an upgrade. We'll get your lights back on fast.
For homeowners and property managers alike, lighting work covers more ground than most people expect. Recessed LED lighting, ceiling fixture installation, under-cabinet lighting, and dimmer-compatible setups are common interior requests. Outdoors, we run circuits for landscape lighting, security lighting, and motion-sensor fixtures that give a property better visibility and deterrence after dark.
Ceiling fan installation is straightforward when existing wiring is in place. When there is no existing wiring in the ceiling, we run the circuit from the panel and install a proper switch leg so the fan and light operate independently. No HVAC work involved, just clean electrical runs and a finished installation.
A straightforward choice for homeowners and property managers, lighting and fan work is easy to schedule and quick to complete.
Arcadia sits in the San Gabriel Valley, where summers run genuinely hot and air conditioning loads push the grid hard during peak season. At the same time, Los Angeles County leads the country in EV adoption, rooftop solar is widespread across the area, and wildfire-season public-safety power shutoffs are a real part of life here. These three services come up constantly in this area because the local conditions make them practical, not optional.
Most Arcadia households with an electric vehicle are still relying on a standard 120-volt outlet, which works but charges slowly. A Level 2 home charger on a dedicated 240-volt circuit cuts overnight charging time significantly. We run the circuit from the panel, check panel capacity before scheduling, and handle the hookup for Tesla wall connectors and universal Level 2 chargers. If the panel needs room for the new circuit, we address that as part of the same job.
When a solar or battery-backup system is ready to connect to the home, the electrical side has to be in order first. We handle the dedicated circuits, disconnect work, and panel or subpanel capacity that allows the system to tie in correctly. We do not install or service the solar equipment itself. What we do is make sure the power infrastructure is ready to support it, which is the part that has to be done right for the system to function safely.
Southern California's grid sees voltage spikes during peak-demand periods, and the surge events that follow can quietly damage electronics, appliances, and HVAC equipment over time. A whole-house surge protector installed at the panel catches those spikes before they reach the circuits inside. It is one of the lower-cost installations we do and one of the more protective ones for a home full of sensitive devices.
We've handled everything from a flickering light to a full rewire, and dedicated circuit work sits somewhere in between: specific, necessary, and often overdue. Electric dryers, stoves, ranges, and hot tubs all require a circuit sized for the load. Running that circuit correctly means the right wire gauge, the right breaker, and a panel that has room for both.
Generator hookups follow the same logic. We install transfer switches for standby and portable generators, wire the hookup to the panel, and make sure the system is set up so the generator cannot back-feed the utility line. For property managers adding appliances to rental units, or homeowners preparing for the next outage season, this is work that is worth scheduling before you need it.
No pressure and no gimmicks, just safe, solid wiring from licensed electricians who know what the job requires.
An electrical inspection tells you what is actually going on inside the walls before something goes wrong. For older Arcadia homes, that can mean uncovering outdated wiring, undersized panels, missing grounding, or protection gaps that were never addressed. For rental properties, a regular inspection is a practical step toward keeping the building code-compliant and the tenants safe.
Pre-purchase inspections are worth scheduling before closing on any property, particularly homes built before the 1980s. We also install hardwired smoke detectors and carbon monoxide detectors as part of inspection follow-up when the existing devices are not up to current standards.
We are accountable to the community we work in, and that means giving you an honest assessment of what the inspection finds, not just a checklist.
For homeowners and property managers alike, the scope of what we handle covers the full range of residential electrical work. For commercial customers, that extends to office and retail electrical work, new construction rough-in, home addition wiring, and commercial repair calls.
Keeping a home safe starts with the wiring behind the walls, and the same principle applies to a commercial space. Tenant improvements, lighting upgrades, panel work for a growing load, and electrical rough-in for new construction all require the same attention to code and the same clean finish. We work with homeowners, landlords, property managers, office and retail tenants, and commercial contractors throughout Arcadia and the surrounding area.
You get the rate on the phone, before anything is scheduled. That means you know what a service call covers and what the work will cost before we confirm the appointment. Same-day service is often available, and we take calls at any hour, including evenings, weekends, and holidays.
Pick the date. We do the wiring. We clean up after.
For urgent situations, calls are answered around the clock. Call (626) 929-3282 and we will confirm pricing and availability on the spot. Call today and we'll set the appointment.
When you call, we ask about the problem, confirm the address, and give you a rate before anything is scheduled. A licensed electrician comes to the property, diagnoses the fault, explains what needs to be done, and completes the work once you have approved the scope. Before leaving, the work is tested and checked against code.
The more detail you can give, the more accurate the rate we can offer. Useful information includes what you are seeing (flickering lights, a dead outlet, a tripping breaker), how old the home or building is, and whether you have had any recent electrical work done. If the scope cannot be confirmed without a site visit, we will tell you that on the call and explain what the diagnostic involves.
Same-day appointments are often available for repairs and troubleshooting in Arcadia and the surrounding San Gabriel Valley communities. For larger jobs like panel replacements or whole-home rewiring, we schedule at your convenience and confirm the timeline on the call. We are available any hour, including evenings, weekends, and holidays, so there is no need to wait for a weekday opening.
We confirm the scope and the rate on the call, then set the appointment. You are told what the visit covers and what to expect before anyone shows up. If anything changes once the electrician is on-site and finds something that was not visible from the outside, that conversation happens before any additional work begins.
Yes. We work with single-family homeowners, landlords, HOAs, multi-family buildings, retail spaces, offices, and commercial contractors throughout Arcadia and Los Angeles County. The process is the same regardless of property type: you call, we confirm the scope and rate, and licensed electricians carry out the work.
A breaker that trips repeatedly is telling you something is wrong, either a circuit that is being asked to carry more than it should, or a wiring fault drawing current it should not be. Resetting it without addressing the cause can damage wiring and create a fire risk over time. Call us and we will diagnose the fault before it becomes a larger problem.
The rate we give on the phone reflects the scope as described. If the electrician arrives and finds something that changes the scope, that conversation happens before the additional work begins, not after. You are not presented with a larger bill without a prior discussion about what changed and why.
Coverage and any applicable travel considerations are confirmed on the call when you give your address. We serve Arcadia and communities throughout the San Gabriel Valley and eastern Los Angeles County, including Monrovia, Temple City, San Gabriel, El Monte, Rosemead, Duarte, Azusa, Pasadena, and Sierra Madre. Call (626) 929-3282 and we will confirm whether your address falls within our service area.
If you cannot be present, let us know when you schedule and we will work out the access details with you on the call. In some cases, leaving a key with a neighbor or providing a lockbox code is enough. What matters is that the electrician can reach the panel and the work area safely.
We serve Arcadia and the communities throughout the San Gabriel Valley and eastern Los Angeles County, including Monrovia, Temple City, San Gabriel, El Monte, Rosemead, Duarte, Azusa, and Pasadena. If your property is in or near any of these areas, we can get someone out to take a look.
G. E. Shears Electric is ready to take your call right now. Reach us at (626) 929-3282 for a quote on any residential or commercial electrical job. Whether it is a repair, an upgrade, or a new installation, call for a quote and we will handle the rest.
Below is a plain-language look at the electrical work we handle across Arcadia and the surrounding San Gabriel Valley communities. Each row covers what the service includes, who it fits best, and one practical thing worth knowing before you call. If a job you need is not listed here, call us and we will tell you whether it falls within our scope.
| Service | Scope of Work | Common Situations | Things to Know |
|---|---|---|---|
| EV Charger Installation | Level 2 charger circuit, 240-volt dedicated run, panel capacity assessment, garage and driveway installation | Arcadia homeowners who have purchased or are planning to purchase an electric vehicle | California's EV adoption rate is among the highest in the country, and demand for this work in the San Gabriel Valley reflects that. If the panel needs an upgrade to support the charger, we handle both in one visit. |
| Dedicated Appliance Circuits | dryer and range circuits, refrigerator and dishwasher circuits, hot tub and spa circuits, workshop and garage circuits | homeowners adding a major appliance, a hot tub, or workshop equipment that needs its own protected circuit | Sharing a circuit between a major appliance and other loads is a common cause of nuisance tripping and wiring wear. A dedicated circuit eliminates both. |
| Hot-Tub Circuits | 240-volt dedicated circuit, disconnect installation, GFCI protection for spa equipment, outdoor conduit and weatherproof wiring | homeowners installing a hot tub or spa who need the electrical side permitted and inspected correctly | Hot tub wiring requires a dedicated circuit, a disconnect within sight of the unit, and GFCI protection. Code requirements for this work are specific and we handle the permit as part of the job. |
| Electrical Panel & Service UpgradesMost Popular | 200-amp service upgrades, full panel replacement, fuse-to-breaker conversion, subpanel installation | older homes adding EV chargers, appliances, or remodel circuits that the existing panel cannot safely carry | We run a load calculation before sizing the replacement so the new service fits the actual demand of the home, not just a round number. |
| Whole-Home Surge Protection | panel-level surge device installation, protection for appliances and electronics, HVAC and EV charger circuit protection, wildfire outage voltage spike coverage | Arcadia households with sensitive electronics, EV chargers, or concerns about grid instability during peak summer and public-safety shutoff events | A panel-level surge protector shields the entire house in one step. It catches voltage spikes from grid events and equipment switching before they reach your devices. |
| Wiring & Circuit Installation | new circuit runs, remodel and addition wiring, grounding and bonding, permit and inspection coordination | kitchen remodels, home additions, and any project that requires new circuits or updated wiring to pass inspection | Permit work is handled as part of the job. The circuit does not go into service until it passes inspection. |
| Standby Battery for Outages | battery backup circuit wiring, critical load panel setup, transfer switch installation, coordination with battery system specs | Arcadia households that need power for critical loads during public-safety shutoff events or grid outages | Southern California's grid sees real stress during peak summer demand and wildfire-season shutoff events. We wire the electrical infrastructure so a battery system can carry the loads that matter most when grid power is unavailable. |
| Ceiling Fan Installation | fan and wiring installation, ceiling box upgrade for fan weight, switch and remote wiring, covered patio fan circuits | bedrooms, living rooms, and covered patios where a fan improves comfort without adding to the cooling load | A standard ceiling box is not rated for a fan's weight and movement. We install the correct rated box before the fan goes up. |
| Breaker & Fuse Repair | breaker replacement, fuse box assessment, tripped breaker diagnosis, panel interior inspection | homes with breakers that trip repeatedly or a fuse box still in service | A breaker that keeps tripping is telling you something. We find out whether the breaker itself is the problem or whether the circuit is simply overloaded. |
| Electrical Repairs & Troubleshooting | dead outlets and switches, flickering or dimming lights, burning smells near receptacles, circuit fault diagnosis | any homeowner or property manager with an electrical problem that needs a fast answer | We find the fault before touching anything else. A proper diagnostic prevents a repair that only masks a deeper wiring issue. |
| Outlet & Switch Installation | GFCI outlet installation, AFCI breaker upgrades, USB outlet installation, dimmer and smart switch wiring | homeowners updating kitchens, bathrooms, garages, or outdoor areas to current code | GFCI protection is required by code in kitchens, bathrooms, garages, and outdoor areas. Installing it correctly means the device trips when it should and not when it should not. |
| Older-Home Rewiring | knob-and-tube removal and replacement, aluminum branch-circuit rewiring, grounding system upgrades, code compliance for older wiring | Arcadia homes with original or early-era wiring that cannot safely carry modern electrical loads | Knob-and-tube and aluminum branch-circuit wiring are both common findings in the San Gabriel Valley's older housing stock. Replacement brings the home to current code and removes risks that older wiring carries under modern loads. |
| Electrical Safety Inspections | pre-purchase and pre-sale assessments, rental property inspections, code compliance reviews, panel and wiring condition reports | buyers, sellers, landlords, and property managers who need a clear picture of a property's electrical condition before a transaction or tenant move-in | In Arcadia's older housing stock, inspections regularly turn up panel issues, missing GFCI protection, and outdated wiring the current owner was not aware of. Catching those items before closing is far less expensive than addressing them after. |
| Solar & Battery Backup | solar-ready panel wiring, battery backup circuits, transfer switch installation, subpanel work for added load | homeowners preparing for solar or battery storage who need the electrical infrastructure done correctly before installation day | We handle the electrical side: wiring, transfer switches, and panel work. We do not install solar panels or battery units themselves. What we deliver is a system that is wired correctly and ready for inspection. |
| Lighting Installation | recessed and LED lighting, outdoor and security lighting, under-cabinet lighting, motion sensor and landscape lighting | homeowners updating a space or adding exterior lighting for security and curb appeal | Outdoor wiring in Southern California needs weatherproof materials and proper conduit on exposed runs. We spec the right materials for the location. |
Call (626) 929-3282 and we will walk through your job, give you a clear rate, and set the appointment on your schedule.
(626) 929-3282